Wire Tracer

Greetings all.



This is my first post here, I hope it goes well.



My name is Joe and I have searched Google. and this forum for my answer but have not been able to find a definitive answer to my question.  I have seen many replies talking about getting a tone generator or a line tracer but my experience is that tone generators are for Data and phone cables rather than electrical cables and the line tracers I've found online all seem to be about tracing the line back to the breaker panel so without knowing more I'm hesitant to purchase a line tracer in case it cannot do what I want.

My dilemma is very likely very simple to anyone with electrical experience so I hope it's not too trivial for this crowd.

I have recently purchased a house that is over 120 years old and have a motion sensor light on the porch that is supposedly connected to a switch inside but does not turn on.  I've opened the wall plate and used a voltage indicating pen to see where the electricity is.  In this case there are two light switches, one that has lines that have been spliced and another that supposedly leads to the porch light according to a long time tenant in that unit.  It all looks like a bit of a mess and the connections don't make sense.  In this scenario the black cables have the electricity and the white cables complete the circuit.  The switch to the porch light has a black cable coming from the top of the box going to the switch and a white cable connected to the other screw that comes from splitting the white cable from the other switch.  What I would like to do is know which cables in that wall box correspond to the cables to the porch light.  Can anyone give me an idea what I should do?

Do I need something like the Amprobe advanced wire tracer (http://www.professionalequipment.com...0/wire-tracer/) and can it do what I need, or is there something simpler I can do?

All help is appreciated.

Thanks



Joe
      

I recently switched over from AT&T phone/cable/Internet service to Cablevision. 



The problem with both services is the coax cable coming through a hole in the wall from outside and then a phone line from their modem stapled to the floor board and tied into the phone outlet inside.  Then there's my phone lines, the coax cable to the TV... It's a disgusting mess.



I'd like to install a combination phone line and cable outlet in the wall and get rid of as much loose wiring as possible.  The phone line would come through the same area as the cable and I'd wire it on the other end to the main box outside the house.



I have no experience with this so my question is can I take the phone line from the Cablevision modem and simply plug it into the outlet and get all the phones in the house to work or does it have to be hard wired or piggybacked inside the outlet?
      

I am new to the forum so kindly bear with me.  I live in Mesa, AZ and have just had a PEX repipe done to bypass my copper hot water lines.  (God don't ask!  A real problem here with slab foundations.  I already had my kitchen jack hammered once.  It is NOT pretty!).

It seems really odd to me that just because it is a dedicated circuit  that code would not require that circuit to be GFCI protected.

I have a dedicated 20 amp duplex 12 AWG wire outlet under the sink and it is within a few inches of the water lines.  The outlet serves a switch for the garbage disposal and serves my dishwasher which is always hot. 

  Now that I have all my maple cabinets pulled out I thought I might change the outlet to a GFCI just to be safe.  I have a ground wire, a red wire, a black wire and a white wire.  As it is dedicated I think I should use the LINE sided instead of the LOAD side but I am not sure where the wires should go.

Could someone give me info on this?  It would be greatly appreciated.  Thank you.
      

I am trying to replace a rocker switch that runs my Panasonic bathroom exhaust fan with a programmable switch that allows me to run the thing automatically several times a day to help suck moisture out of the condo (it's a 1962 condo with concrete walls, aluminum windows, and no central air).



I initially bought a GE SunSmart Timer but it requires a neutral, which I don't think I have. I understand there are some other switches like Intermatic ones that don't require neutrals.



I don't think I have a neutral because the condo is old and I don't see a white wire in the box, but what's strange is that I do see an unconnected orange wire in there. Does anybody know what that could be? Image is attached. Essentially there are 2 blues, 1 red, 1 black, and 1 orange (unconnected) in there. The only thing I can find about orange wires is something called a "high leg delta" circuit, which seems reasonable because it's supposedly used to control fans and lights off the same circuit, which is exactly what's going on here (one can light, one heat lamp, and one fan).



Any ideas?
      

We're running a new electrical wire & wondering if it would be ok to place it where indicated in the pic... or should we cut out more wall to the left & get it away from the water lines?
      

Helicopter flies inches from LIVE electrical power lines so daredevil repairman can fix them



    But because the power lines serve  400,000 people, the line cannot be closed down, meaning the work needs  to be done while the line is live. 



   Highlighting  the dangers of the work, the commentator on the film says: 'These lines  are still energised; we are flying right at them in a big hunk of  metal filled with jet fuel.'



Read mo     http://www.dailymail.co.uk/news/arti...#ixzz1spBXQymz
      

Hello, I'm roughing in 5 rooms and it's time to do the cable boxes. I was thinking of using RG 6/U in each room with home runs for every room.

I'm not sure really what to use.



This is rental property, and some tenants use Satelite, some use "Charter"

and all use High Speed Internet.

I'm thinking of also installing Cat 5E or 6 in same box.



I only want to do this once since I can't pull it out once installed.

Not sure about telephone, probably cable, but I might run some 22/4

in same box just in case. Hopefully crosstalk will not be an issue.



Any help or ideas would be appreciated.



Thanks.
      

i think our dishwashers control board is messed up. i think i heard i can test whether it is working with a multimeter or not. if so how can i? the cycles options a  pots/pans, normal wash, water miser, china gentle, and quick rinse. only the china gentle option works. the three other separate options a  high temp scrub, santi-rinse, and air dry. none of these work... also the delay hours options do not work either. and when i try to cancel or drain it, it will not stop unless u open it (but when u shut it, it starts until it finishes.) can all of this be fixed if i replace the control board? or do u think it will fix it if i change the fuses? or both? if not, what other problems could be causing this?
      

Each time someone drives by my house using a cell phone it seems there is a one-time clicking noise coming out of several of my electrical outlets.  It may happen in all rooms at the same time but of course, the only ones I notice are in the room I am in currently.



Any ideas, and thanks!
      

I want to run a Cat 5 line from my phone box outside to a jack inside to connect my phone and DSL. Right now I just have a regular phone line for both and the phone company recommends running a new line because the internet is always slow and I can't call out on my phone.



How do I know which wires to hook up outside?



Kevin